|
Specification |
|
|
Operating voltage |
DC 11~18 volts |
|
Idling current |
approx. 100mA |
|
Charge/discharge power |
max. 200/25W |
|
NiCd/MH |
1~18 cells |
|
LiIo/LiPo/LiFe |
1~6 series |
|
Pb |
2~24V |
|
Charge current |
0.1 to 10.0A |
|
Discharg current |
0.1 to 5.0A |
|
No. of cycle |
1 to 5 times |
|
Battery data memory |
up to 10 data |
|
Weight |
960g |
|
Dimension |
160x120x40 mm |
click the picture to enlarge
|
User's setting-up parameters |
|
|
Lithium battery voltage type |
LiIo:3.6V, LiPo:3.7V, LiFe:3.3V |
|
NiCd Delta-peak voltage sensitivity |
5 to 20mV |
|
NiMH Delta-peak voltage sensitivity |
5 to 20mV |
|
Battery temperature cut-off |
20 to 80C or OFF |
|
Waste time between charge/discharge |
1 to 60 min. |
|
Trickle charge mode |
ON/OFF, up to 200mA |
|
Integral timer limit for safety |
10 to 720 min.or OFF |
|
Maximum charging capacity limit for safety |
10 to 9990mAh or OFF |
|
Key beep and buzzer sound |
ON/OFF |
|
Input power low alert |
10 to 11V |
|
LCD back-light brightness |
1 to 100 steps |
- Operating software
Every operating program in the unit is controlled with mutual links and communications to prevent every possible error, so it introduces the maximum safety, such as input voltage warning, reverse polarity protection and Lithium cell-count input error warning.
- High-power and high-performance circuit
BC6-10 employs the circuit that has maximum output power of 200Watts. As a result, it can charge or discharge up to 18 cells of NiCd/NiMH and 6 series of Lithium batteries with maximum current of 10A. Furthermore, the cooling system is so efficient that can hold such a power without any trouble of running the circuit or the operating program.
- Individual voltage balancer for Lithium batteries inside
BC6-10 has an individual-cell-voltage balancer inside. So it does not need any balancer separately when charging Lithium batteries (LiIo/LiPo/LiFe) for cell voltage balancing.
** When the 'Balance charge' mode being performed, the balancing adapter should be connected to the balancing tab of battery pack, as well as the charger's charging lead should be connected to the output of battery pack.
And also, please pay attention to the polarity of the battery pack's output which goes to the charger's output. If it is reversed, the short-circuit can be happened on the battery pack.
- Accept various types of Lithium battery
BC8 can accept three types of Lithium batteries - LiIo, LiPo and LiFe. They have different characteristics by their chemistry. You can select any one of them that you are going to process before the job.
- Lithium battery 'Fast' and 'Storage' mode
You can charge Lithium battery for special purposes. 'Fast' charge reduces the charging time of Lithium battery and 'Storage mode controls the final voltage of the battery to be suit for long time storage.
- Data store/load
For users convenience it can store maximum 10 data of different batteries. You can establish the data contains program setting of the battery to charge or discharge continually. These data can be called out at any time you need and the process can be executed without program setting.
- Cyclic charging/discharging
Perform 1 to 5 cycles of charge>discharge or discharge>charge continually for battery refreshing and balancing.
- PC based analysis using USB communication
For technical expert, BC6-10 offers PC based program can analysis the characteristic of the battery by USB port. It shows a graph of voltage, current, capacity and temperature curves. It also shows the individual voltage of each cell in the Lithium battery pack.
- Back-light LCD screen
You can adjust the brightness of LCD display
- Robust outer aluminum case
High-quality aluminum case is durable and very efficient to cool out the internal heat
|
Accessories |
||
|
Temperature sensor cable |
Optional |
|
|
4mm gold banana plug with silicon cable and alligator clips |
Standard |
|
|
8-pin cable for individual cell connector |
Optional |
|
|
Charge graph program kit (CD + USB cable) |
Optional |
|
